I can ping pfSense fine, I'm trying to ping my Cisco ADSL router that is the default gateway for the LAN. I'd be surprised if it were a pfSense firewall for two reasons 1 - The firewall rules wouldn't change from when I'm at work to when I'm at home, so I'd expect the same behaviour at both locations
Cannot ping server or default gateway Windows 10 So over the past couple of weeks my DSL connection keeps dropping. Well, actually, to be clear the connection remains stable, but it fails to "ping primary domain name server" and "ping default gateway." I have a virtual network which is vmnet2 using the 10.0.2.0/24 network, I want my Linux server to be able to ping the default gateway. I have set the Linux eth1 values to be IPADDR="10.0.2.50" I am unable to connect to internet since I am unable to ping my default gateway 192.168.1.2 from a virtual machine. Its was working properly but after I restarted the virtual machine I couldnt ping the default gateway. I also tried pinging the default gateway from another virtual machine, but still i didnt get any response. Jul 27, 2012 · Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.1.1 Default I took a look at one of my physical machines on the same 10 network and the routes are the same as I show on the Xen VMs. I did however add a persistent route (route add -p 10.0.1.81 mask 255.255.0.0 10.0.1.1) to one of the VM guest and it still can not ping the I am unable to ping my ISP default gateway from the 2911/K9. I have verifed the ISP connection by directly connecting the cable to my laptop with static ip addresses. Here is the running config and show version. Any help is greatly appreciated. Thanks! Current configuration : 1468 bytes ! ! Last c 2. Ping your default gateway. Note: Only perform this task if the Endpoint where you're trying to remotely install the Endpoint Agent is in a different subnet. On the Endpoint with the Management Server, press Windows Key + R. Type cmd and press Enter. In the console, type ipconfig and press Enter. If you see an entry like this: Default Gateway
Ping statistics for 192.168.28.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),-----I tested connecting a PC to te1/0/1 port on the switch setting it to an access vlan 280 and I am able to ping the PC, which indicates that inter-vlan routing is working. So any ideas as to why I can't ping the vlan interfaces on the switch except for one?
The service macafee_privacy_service when shut down would allow traffic to 192.168.1.1 via a dos prompt ping. When this service was up, I could not get to the default gateway or any where else. I don't know why it started having this effect all of a sudden, it had been installed for over a year without issue.
Re: Wifi client unable to ping it's default gateway, and WLC can not ping User-Vlan Gateway 01-10-2020 05:01 AM If you don't have the basics working, it is really hard to help you in this forum with limited information.
May 21, 2010 · Unable to ping the gateway: Setya: Linux - Networking: 5: 08-06-2007 01:16 AM: Unable to PING default gateway, SUSE 10.1: LTC Don: Linux - Networking: 1: 10-07-2006 12:25 PM: Unable to ping other than default gateway: senthilpr_in: Linux - Networking: 6: 08-17-2005 07:42 PM: PPP establish can ping the gateway router but unable to ping the host A gateway is a node or a router that acts as an access point to passes network data from local networks to remote networks. There are many ways to find out your gateway in Linux. Here are some of them from Terminal. You can find default gateway using ip, route and netstat commands in Linux systems. Using route command Aug 30, 2012 · Hi all, would be great if someone can help with the following: Trying to setup a VPN connection to Azure but running into problems. For debugging purposes I am trying to ping the default gateway from a VM in Azure via RDP, but I do not get any response. Our firewall/ default gateway is a Juniper Networks SSG-140. The problem: Every 20 to 30 minutes, while all employees are in the office (doesn't seem to happen after hours), our Small Business Server loses the ability to communicate with the default gateway. I can't ping the default gateway, can't get out to the internet, etc Ping statistics for 192.168.28.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),-----I tested connecting a PC to te1/0/1 port on the switch setting it to an access vlan 280 and I am able to ping the PC, which indicates that inter-vlan routing is working. So any ideas as to why I can't ping the vlan interfaces on the switch except for one?